Climate Control

PolAir High Pressure Fogging

PolAIR High Pressure Fog systems atomize water into micro-sized particles that rapidly evaporate to reduce air temperature. Due to this evaporative cooling process warmth is extracted from the air used for the evaporation of water. The fog increases the relative humidity and suppresses airborne contaminants. PolAIR is the system that can effectively control the temperature and the relative humidity as needed in green houses.

The unique VAL-CO PolAIR nozzle is completely made from stainless steel and produces the finest fog giving the highest cooling effect without any condensation on the floor.

PolAIR is renowned for its high reliability and yearlong smooth operation with minimum maintenance. The systems operate at pressures of 1000 to 1500 psi (from 70 to 105 bar) with an average particle size of 10 – 15 microns. At mentioned pressures, the PolAIR nozzle atomizes 6,2 – 7,7 l/hour and 2,5 – 4,0 gr of moisture/m3 air.

All systems are individually configured, and tailor made to fit your situation.

Features & Benefits

  • Nozzles produce the finest fog giving the highest cooling effect
  • Increase relative humidity and suppress airborne contaminants
  • Operational pressures of 1000 to 1500 psi (70 to 105 bar)
  • Systems are individually configured

Request A Quote

PolAIR EZ-Cool™ Pad Cooling

pad cooling

PolAIR EZ-Cool Pad Cooling systems offer efficient evaporative cooling. The raised ribbed pad tray keeps the pad elevated above drain holes to increase the life of the pad. The trough drains completely and has a full 18″ clean-out for easy maintenance. Install the pad cooling system offset from the wall or flush onto the wall.

Features & Benefits

  • Raised ribbed pad tray keeps pad elevated above drain holes
  • 100% drainage with to tray spillover
  • Quick connect coupler for quick installation
  • Full 18″ cleanout for easy maintenance

Options

  • Extended – allows pad material to be offset from the wall by 10″
  • Flush – direct installation onto the wall
  • Open-top

Request A Quote

Heat-Rite VM Modulating Heater

Heat-Rite VM Modulating Heaters use infrared heat to warm the floor and birds. Modulating controls the burn and blower rates to balance radiant heat and thermal heat. A broad range of burner sizes and tube lengths are available to fit the needs of any barn.

Features & Benefits

  • Modulation controls burn and blower rates to balance radiant and thermal heat
  • Infrared heat warms floor and birds
  • Mounted to ceiling for wide, even coverage
  • Broad range of burner sizes and tube lengths available

Aurora IR Brooders

The Aurora IR Brooder has a low 11″ profile for better clearance in the house. The canopy can be aluminum or galvanized and the brooder ships fully assembled for quick installation. the 40,000 BTU/hr rating is sure to keep chicks warm. Choose between a horizontal pilot or a pilot-free direct spark ignition.

Features & Benefits

  • Low profile for better clearance throughout the house
  • 34″ (86cm) canopy in aluminum or galvanized
  • 40,000 BTU/hr (10,100 k/cal) rating
  • Ships fully assembled for quick installation

Options

  • Horizontal pilot
  • Pilot-free direct spark

Radiant Brooders

The Heat-Rite Radiant Brooder uses infrared heat to warm the floor and chicks. A leveler bracket adjusts the heater side to side and front to back, so you can keep it in just the right position. Choose between a horizontal pilot, vertical pilot, or pilot-free direct spark ignition.

Features & Benefits

  • Infrared heat warms floor and chicks without wasting heat on the air
  • Leveler brackets to adjust heater side to side and front to back
  • 34″ (86cm) canopy
  • 40,000 BTU/hr (10,100 k/cal) rating
  • Liquid propane or Natural Gas

Options

  • Horizontal pilot
  • Vertical pilot
  • Pilot-free direct spark

Heat-Rite ES Tube Heat

The Heat-Rite ES Tube Heater creates a wide, even heat pattern to heat more area of the floor. The sealed control housing requires less maintenance and cleaning than conventional brooders. Available in a single-tube or u-tube configuration.

Features & Benefits

  • Creates an even heat pattern
  • Wide pattern reflector to heat more floor
  • Sealed control housing requires less maintenance and cleaning

Options

  • Single-tube